如何安装LINUX+windows(很有挑战)光软，不能网卡启动。详细看内容。

linux_pro

1. We get this question a lot lately.  Thanks to Robert Hentosh for providing
2. this information.  I've also posted this to the FAQ.
3. -Matt
6. Installing Red Hat Linux 7.2 on a PowerEdge 2600
8. The PowerEdge 2600 has advanced features that is not supported by the
9. 2.4.7-10 kernel contained in the Red Hat Linux 7.2 install media.  It is
10. necessary to install Red Hat Linux 7.2 using the UP kernel and Dell supplied
11. drivers for the Storage Controllers.
13. The PowerEdge 2600 can be configured with either a PERC controller or
14. the LSI SCSI controller.
16. Please download the device drivers from support.dell.com and make
17. device driver diskettes as per the instructions accompanying the
18. download.
20. At the time of this writing the following files were available:
22. SCSI RAID:
23.   PERC 3/QC and PERC 3/DC:
24.         perc3-118c-72e.tar.gz
25.   PERC 4/DI:
26.         perc4di-118c-72c.tar.gz       
29. SCSI Non-RAID:
30.   LSI Logic Ultra 320 SCSI v 2.00.11, A00:
31.         22320-linux-2.00.11.tar.gz
32.         mptlinux-2.00.11rpm.tar.gz
33. * NOTE You will need both files. The mptlinux-2.00.11rpm.tar.gz file
34.   may appear under "Previous versions" on the support.dell.com
35.   website.
38. Also you will need to download a patched 2.4.7-10 kernel that contains
39. the changes necessary to operate on the PE2600.  Please obtain the
40. 2.4.7-10a kernel from Red Hat's support site:
41. http://www.redhat.com/support/errata/partners/dell/.  The link on that
42. page will take you to an FTP
43. site. (ftp://ftp.redhat.com/pub/redhat/support/enterprise/dell/2.4.7-10a/i686/)
45. You can download the kernel-smp-2.4.7-10a.i686.rpm and the
46. kernel-enterprise-2.4.7-10a.i686.rpm.  You will only need to install
47. one of those kernels.  Install the smp rpm if you have a system with
48. less than 4GB of RAM.  Install the enterprise rpm if you have more
49. than 4GB of RAM.
51. If you are installing on a SCSI RAID system skip ahead to the next section:
53. SCSI Non-RAID:
55. * Boot your PE2600 with DISC 1 of the Red Hat Linux 7.2 media.
56. * At the boot: prompt, type "linux dd" to prompt the install to permit
57.   driver diskettes.
58. * When prompted, if you have a driver diskette, select YES.
59. * Insert the driver diskette previously made from the file
60.   22320-linux-2.00.11.tar.gz
61. * Continue the install following the on screen instructions
62. * When prompted select GRUB as the bootloader.
63. * When prompted to "Boot Disk Creation":
64.         o Press CTRL-ALT-F2 to switch to the install shell console.
65.         o Type  the following commands:
67.                 chroot /mnt/sysimage
68.                 cd /boot
69.                 /sbin/mkinitrd -f initrd-2.4.7-10.img 2.4.7-10
71. * Ignore the error message about "binary operator expected"
72. * If you used LILO as the boot loader you will have to rerun lilo to
73.   handle the change just made to the initrd.
75.                 exit
77.         o Press CTRL-ALT-F7 to return to the install screens.
79. * Remove the driver diskette if you already haven't
80. * Continue the install and reboot your machine
81. * You must now select the UP kernel (2.4.7-10)
82. * Login as root using the password you supplied during the install.
83. * Remove the current smp kernel
85.                 rpm -e kernel-smp
87. * Transfer the 2.4.7-10a kernel over and install
89.                 rpm -ivh kernel-smp-2.4.7-10a.i686.rpm (for systems <
90.                 4GB RAM)
91.                 rpm -ivh kernel-enterprise-2.4.7-10a.i686.rpm (for
92.                 systems > 4GB RAM)
94. * Transfer the mptlinux-2.00.11rpm.tar.gz
95. * Untar the mptlinux-2.00.11rpm.tar.gz file
97.                 tar -xvzf mptlinux-2.00.11rpm.tar.gz
99. * Install the mptlinux rpm.
101.                 rpm -ivh mptlinux-2.00.11-0.i386.rpm
103. * Edit the grub.conf file to change the default kernel to the SMP
104.   enabled one by changing the default=1 line to default=0
105. * Reboot into the SMP enabled kernel
107.                 reboot
109. The install is now complete. You should also update your Network
110. Adapter drivers, which can be obtained at http://support.dell.com
113. SCSI RAID:
115. Using the driver diskette for the appropriate Power Edge Raid
116. Controller (PERC) contained in your machine:
118. * Boot your PE2600 with DISC 1 of the Red Hat Linux 7.2 media.
119. * At the boot: prompt, type "linux dd" to prompt the install to permit
120.   driver diskettes.
121. * When prompted, if you have a driver diskette, select YES.
122. * Insert the driver diskette previously made for your PERC and press enter.
123. * Continue the install following the on screen instructions
124. * When prompted select GRUB as the bootloader.
125. * When prompted to "Boot Disk Creation":
126.         o Press CTRL-ALT-F2 to switch to the install shell console.
127.         o Type  the following commands:
129.                 chroot /mnt/sysimage
130.                 cd /boot
131.                 /sbin/mkinitrd -f initrd-2.4.7-10.img 2.4.7-10
133. * If you used LILO as the boot loader you will have to rerun lilo to
134.   handle the change just made to the initrd.
136.                 exit
138.         o Press CTRL-ALT-F7 to return to the install screens.
140. * Remove the driver diskette if you already haven't
141. * Continue the install and reboot your machine
142. * You must now select the UP kernel (2.4.7-10)
143. * Login as root using the password you supplied during the install.
144. * Remove the current smp kernel
146.                 rpm -e kernel-smp
148. * Transfer the 2.4.7-10a kernel over to your PE2600 and install
150.                 rpm -ivh kernel-smp-2.4.7-10a.i686.rpm (for systems <
151.                 4GB RAM)
152.                 rpm -ivh kernel-enterprise-2.4.7-10a.i686.rpm (for
153.                 systems > 4GB RAM)
155. * Insert the driver diskette again and run the install script
157.                 mount /mnt/floppy
158.                 cd /mnt/floppy
159.                 ./megarpmwrapper.sh
161.         o Aswer yes to "install dialog" and to "rpm -ivh"
162.         o Press enter when prompted for command line options for rpm.
163.         o When prompted for the "Initial RAMDISK" use:
165.                         2.4.7-10asmp
166.                 or
167.                         2.4.7-10aenterprise
169.         o Change the name of the initrd image:
171.                         initrd-2.4.7-10asmp.img
172.                 or
173.                         initrd-2.4.7-10aenterprise.img
175.         o Select User Level NOVICE.
176.         o Select EXIT (press enter)
177.         o Select Yes to proceed (press enter)
178.         o Select OK to specify GRUB as your bootloader. (press enter)
179.         o Select OK (press enter)
180.         o Select vi (press enter)
181.         o Exit the editor  (press "ESC" then ":q" and enter)
182.         o Eject the floppy and select NO to skip reboot (press enter)
184. * Edit the grub.conf file to change the default kernel to the SMP
185.   enabled one by changing the default=1 line to default=0
187. The install is now complete. You should also update your Network
188. Adapter drivers, which can be obtained at http://support.dell.com

复制代码

Dell PERC4/SC (LSI MegaRAID SCSI 320-1) single-channel Ultra320 RAID storage adapter

应该是这个适配器.
LSI.....

糊涂

“他已经支持了RAID”
关键看你机器是哪种RAID卡，要先找出你RAID卡的具体型号，最好是准确的型号。可能的话放个照片上来。
然后查OS硬件兼容列表，或者到卡的厂家主页查相应OS驱动。

糊涂

LSI MegaRAID SCSI 320-1，大概是三、四年前的产品吧，成熟产品，驱动很全。Ultra320 SCSI单通道RAID卡。
好了，卡的型号有了。

linux_pro

Post by 糊涂
LSI MegaRAID SCSI 320-1，大概是三、四年前的产品吧。Ultra320 SCSI单通道RAID卡。

好了，卡的型号有了，你要装什么OS？不会是RH7.2吧？

Post by 糊涂
LSI MegaRAID SCSI 320-1


好了，卡的型号有了，你要装什么OS？不会是RH7.2吧？

Please download the device drivers from support.dell.com and make
device driver diskettes as per the instructions accompanying the
download.
英文很差,粗略看了整个文章,发现 没有raid模式的适合机器(本来机器有两块磁盘的,结果被拔走了一块,所以不能raid模式)
RH7.2是需要下载驱动编译的.不过我看不太明白.因为别个的机器是有完整的配制,而我使用的是没有光软的,所以她没特别提示这种方式是 光驱?
那个熟悉en 的同学指点下....我该睡觉了..

呵呵,我熟悉什么安装什么啦.先考虑suse,不行考虑k.i.s.s.

clxer

Post by 糊涂
刚才敲了一大段，提交时又被告知“未登录”。真tmd郁闷，只好写几个字就提交一下。

这是浏览器cockie的问题。

想当初玩DOS的时候，linux还没有诞生，现在玩linux就像当初玩DOS，惭愧啊

糊涂

Post by linux_pro
Please download the device drivers from support.dell.com and make
device driver diskettes as per the instructions accompanying the
download.
英文很差,粗略看了整个文章,发现 没有raid模式的适合机器(本来机器有两块磁盘的,结果被拔走了一块,所以不能raid模式)
RH7.2是需要下载驱动编译的.不过我看不太明白.因为别个的机器是有完整的配制,而我使用的是没有光软的,所以她没特别提示这种方式是 光驱?
那个熟悉en 的同学指点下....我该睡觉了..

呵呵,我熟悉什么安装什么啦.先考虑suse,不行考虑k.i.s.s.

根据本人有限的知识和经验，对于RAID卡连接SCSI硬盘这种情况，一般来说无论你接了几块硬盘都需要创建RAID才能够让OS访问到，象你这样虽然只连了一块硬盘，也必须做一个RAID，你可以创建一个只有一块硬盘的“RAID 0”或者用这块盘创建一个“JBOD”（注意：创建后，原来盘上的数据就全部丢失了。必要的话，事先做好数据备份）不过具体到你现在这块卡是否也必须创建RAID还是要实验一下。

linux_pro

Post by 糊涂
根据本人有限的知识和经验，对于RAID卡连接SCSI硬盘这种情况，一般来说无论你接了几块硬盘都需要创建RAID才能够让OS访问到，象你这样虽然只连了一块硬盘，也必须做一个RAID，你可以创建一个只有一块硬盘的“RAID 0”或者用这块盘创建一个“JBOD”（注意：创建后，原来盘上的数据就全部丢失了。必要的话，事先做好数据备份）不过具体到你现在这块卡是否也必须创建RAID还是要实验一下。

1. The Standard Kernel
2. The New Default File System: ext3
3. Setting Up LVM and EVMS with YaST
4. SMART Disk Monitoring Daemon (smartd)
5. [color="Red"]BIOS RAID Supported During Installation
6. Booting Multiple Instances of openSUSE on One System
7. GRUB or LILO Left Over in the MBR from a Previous Installation
8. X.Org-Specific Changes for Developers
9. New Power Management Options
10. Booting Systems with HPET Timer Problems

这个是 SUSE10.2发行注释！ ：）

再次感谢兄弟关注此帖。今天刚刚考完 数据结构。呵呵。

糊涂

BIOS RAID is now supported during installation. Activate it in the BIOS and run a default installation.
就这么一句，说得不明不白的。啥叫BIOS RAID？明白人给上上课。