请问如何mount U盘啊？——求助

cghphys

dmesg | grep -i usb 输出以下信息：

[   20.687290] usbcore: registered new interface driver usbfs
[   20.687443] usbcore: registered new interface driver hub
[   20.687597] usbcore: registered new device driver usb
[   23.768272] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[   23.787109] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   23.794937] usb usb1: configuration #1 chosen from 1 choice
[   23.802734] hub 1-0:1.0: USB hub found
[   23.919694] USB Universal Host Controller Interface driver v3.0
[   23.943141] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[   23.958765] usb usb2: configuration #1 chosen from 1 choice
[   23.966524] hub 2-0:1.0: USB hub found
[   24.099275] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[   24.114991] usb usb3: configuration #1 chosen from 1 choice
[   24.122785] hub 3-0:1.0: USB hub found
[   24.253415] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[   24.268446] usb usb4: configuration #1 chosen from 1 choice
[   24.275875] hub 4-0:1.0: USB hub found
[   24.793745] usb 2-1: new low speed USB device using uhci_hcd and address 2
[   24.965045] usb 2-1: configuration #1 chosen from 1 choice
[   25.181455] usb 2-2: new full speed USB device using uhci_hcd and address 3
[   25.346775] usb 2-2: configuration #1 chosen from 1 choice
[   25.356657] hub 2-2:1.0: USB hub found
[   25.698293] usbcore: registered new interface driver usblp
[   25.704977] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[   25.724497] input: Logitech USB-PS/2 Optical Mouse as /class/input/input0
[   25.731275] input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-1
[   25.738242] usbcore: registered new interface driver usbhid
[   25.745076] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 1832.474336] usb 2-2: USB disconnect, address 3
[ 1832.578223] usb 2-2: new full speed USB device using uhci_hcd and address 4
[ 1832.737585] usb 2-2: configuration #1 chosen from 1 choice
[ 1832.740564] hub 2-2:1.0: USB hub found
[ 7215.189162] usb 2-2.2: new full speed USB device using uhci_hcd and address 5
[ 7215.313201] usb 2-2.2: configuration #1 chosen from 1 choice
[ 7288.685541] usb 2-2.2: USB disconnect, address 5
[ 9793.602717] usb 2-2.2: new full speed USB device using uhci_hcd and address 6
[ 9793.726751] usb 2-2.2: configuration #1 chosen from 1 choice


fdisk -l 输出以下信息：

Disk /dev/hda: 81.9 GB, 81964302336 bytes
255 heads, 63 sectors/track, 9964 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

   Device Boot      Start         End      Blocks   Id  System
/dev/hda1   *           1        1697    13631121    7  HPFS/NTFS
/dev/hda2            1698        9964    66404677+   f  W95 Ext'd (LBA)
/dev/hda5            1698        4247    20482843+   7  HPFS/NTFS
/dev/hda6            4248        7434    25599546    b  W95 FAT32
/dev/hda7   *        7435        7439       40131   83  Linux
/dev/hda8            7440        7564     1004031   82  Linux swap / Solaris
/dev/hda9            7565        8810    10008463+  83  Linux
/dev/hda10           8811        9184     3004123+  83  Linux
/dev/hda11           9185        9434     2008093+  83  Linux
/dev/hda12           9435        9964     4257193+  83  Linux

好像没有U盘喔，怎么找到我的U盘呢？

bpxyz

modprobe usb-storage后再看看

blackwhite

你插入Ｕ盘的后，dmesg里边有/dev/sd?的消息。
如果你要自动mount，需要安装hal,ivman, pmount。
看看这个。
http://gentoo-wiki.com/HOWTO_D-BUS%2C_HAL%2C_KDE_media:/

cghphys

上面那个信息就是我已经插了U盘后的信息了。

zhllg

http://www.gentoo.org/doc/en/usb-guide.xml